#Bash 的 mkswap 命令

MKSWAP(8)                    System Administration                   MKSWAP(8)

NAME
       mkswap - set up a Linux swap area

SYNOPSIS
       mkswap [options] device [size]

DESCRIPTION
       mkswap sets up a Linux swap area on a device or in a file.

       The device argument will usually be a disk partition (something like
       /dev/sdb7) but can also be a file. The Linux kernel does not look at
       partition IDs, but many installation scripts will assume that
       partitions of hex type 82 (LINUX_SWAP) are meant to be swap partitions.
       (Warning: Solaris also uses this type. Be careful not to kill your
       Solaris partitions.)

       The size parameter is superfluous but retained for backwards
       compatibility. (It specifies the desired size of the swap area in
       1024-byte blocks. mkswap will use the entire partition or file if it is
       omitted. Specifying it is unwise - a typo may destroy your disk.)

       After creating the swap area, you need the swapon(8) command to start
       using it. Usually swap areas are listed in /etc/fstab so that they can
       be taken into use at boot time by a swapon -a command in some boot
       script.

WARNING
       The swap header does not touch the first block. A boot loader or disk
       label can be there, but it is not a recommended setup. The recommended
       setup is to use a separate partition for a Linux swap area.

       mkswap, like many others mkfs-like utils, erases the first partition
       block to make any previous filesystem invisible.

       However, mkswap refuses to erase the first block on a device with a
       disk label (SUN, BSD, ...).

OPTIONS
       -c, --check
           Check the device (if it is a block device) for bad blocks before
           creating the swap area. If any bad blocks are found, the count is
           printed.

       -f, --force
           Go ahead even if the command is stupid. This allows the creation of
           a swap area larger than the file or partition it resides on.

           Also, without this option, mkswap will refuse to erase the first
           block on a device with a partition table.

       -q, --quiet
           Suppress output and warning messages.

       -L, --label label
           Specify a label for the device, to allow swapon(8) by label.

       --lock[=mode]
           Use exclusive BSD lock for device or file it operates. The optional
           argument mode can be yes, no (or 1 and 0) or nonblock. If the mode
           argument is omitted, it defaults to yes. This option overwrites
           environment variable $LOCK_BLOCK_DEVICE. The default is not to use
           any lock at all, but it’s recommended to avoid collisions with
           systemd-udevd(8) or other tools.

       -p, --pagesize size
           Specify the page size (in bytes) to use. This option is usually
           unnecessary; mkswap reads the size from the kernel.

       -U, --uuid UUID
           Specify the UUID to use. The default is to generate a UUID. The
           format of the UUID is a series of hex digits separated by hyphens,
           like this: "c1b9d5a2-f162-11cf-9ece-0020afc76f16". The UUID
           parameter may also be one of the following:

           clear
               clear the filesystem UUID

           random
               generate a new randomly-generated UUID

           time
               generate a new time-based UUID

       -e, --endianness ENDIANNESS
           Specify the ENDIANNESS to use, valid arguments are native, little
           or big. The default is native.

       -v, --swapversion 1
           Specify the swap-space version. (This option is currently
           pointless, as the old -v 0 option has become obsolete and now only
           -v 1 is supported. The kernel has not supported v0 swap-space
           format since 2.5.22 (June 2002). The new version v1 is supported
           since 2.1.117 (August 1998).)

       --verbose
           Verbose execution. With this option mkswap will output more details
           about detected problems during swap area set up.

       -h, --help
           Display help text and exit.

       -V, --version
           Print version and exit.

ENVIRONMENT
       LIBBLKID_DEBUG=all
           enables libblkid debug output.

       LOCK_BLOCK_DEVICE=<mode>
           use exclusive BSD lock. The mode is "1" or "0". See --lock for more
           details.

NOTES
       The maximum useful size of a swap area depends on the architecture and
       the kernel version.

       The maximum number of the pages that is possible to address by swap
       area header is 4294967295 (32-bit unsigned int). The remaining space on
       the swap device is ignored.

       Presently, Linux allows 32 swap areas. The areas in use can be seen in
       the file /proc/swaps.

       mkswap refuses areas smaller than 10 pages.

       If you don’t know the page size that your machine uses, you can look it
       up with getconf PAGESIZE.

       To set up a swap file, it is necessary to create that file before
       initializing it with mkswap, e.g. using a command like

           # dd if=/dev/zero of=swapfile bs=1MiB count=$((8*1024))

       to create 8GiB swapfile.

       Please read notes from swapon(8) about the swap file use restrictions
       (holes, preallocation and copy-on-write issues).

SEE ALSO
       fdisk(8), swapon(8)

REPORTING BUGS
       For bug reports, use the issue tracker at
       https://github.com/util-linux/util-linux/issues.

AVAILABILITY
       The mkswap command is part of the util-linux package which can be
       downloaded from Linux Kernel Archive
       <https://www.kernel.org/pub/linux/utils/util-linux/>.

util-linux 2.39.3                 2023-12-01                         MKSWAP(8)